FM1125
FM1125FM1125FM1125

FM1125 – RS232 + RS485

Small Tracker with RS232 and RS485 interfaces and back-up battery

Technology
  • SMS
  • GPRS
  • GNSS
Hardware
  • 16MB memory
  • Battery
  • RS485
  • RS232
Firmware
  • Transparent mode (RS232)
  • Fuel monitoring LLS
  • RFID RS232
  • LV-CAN support

Compare products
(Compare 2 or up to 4 products)

Product Description

Small Tracker with RS232 and RS485 interfaces

  • RS232/RS485 peripheral device support (GARMIN FMI support, Digital LLS fuel sensors support, RFID protocol support, LCD mode support)
  • 16MB flash memory
  • LVCAN200, ALL-CAN300 functionality support
  • Internal GSM and GPS/GLONASS antennas
  • Integrated backup battery
  • Integrated scenarios (Overspeeding, Authorized driving, Immobilizer)

FM1125 Scheme

FM1125TBX5SC* package contains

  • FM1125 tracker.
  • Mini USB – USB cable (0.8 m).
  • Input/output power supply cable (0.9 m).

* SAMPLES ordering code – applied for orders up to 7 pcs.

FM1125TBX501* package contains

  • FM1125 tracker.
  • Mini USB – USB cable (0.8 m).
  • Input/output power supply cable (0.9 m).

* MASS PACKAGING – for bigger quantity orders, with configuration cable included.

FM1125TBTV01* package contains

  • FM1125 tracker.
  • Input/output power supply cable (0.9 m).

* MASS PACKAGING – for bigger quantity orders, configuration cable not included.

  • TECHNOLOGY

  • GNSS i Global positiong system/Global Navigation Satellite System.
  • GPRS i General Packet Radio Service (GPRS) is a packet oriented mobile data service based on the 2G technology.
  • SMS i Short Message Service (SMS) is a text messaging service component.
  • HARDWARE

  • Internal GSM antenna i An antenna used for GSM connectivity. Integrated into FM device PCB. Does not have external connector.
  • Internal GNSS antenna i An antenna used for GPS connectivity. Integrated into FM device PCB. Does not have external connector.
  • RS232 –1 i RS-232 is a standard for serial communication transmission of data
  • RS485 –1 i RS-485 is a standard defining the electrical characteristics of drivers and receivers for use in serial communications systems
  • DIN – digital input –1 i Digital Inputs allow device to detect logic states 1 (enabled) or 0 (disabled).
  • AIN - analog input –1 i An analog input converts a voltage level into a digital value that can be stored and processed in device.
  • DOUT –1 i Digital Outputs allow device to output logic states 1 (makes a circuit) and 0 (cuts the circuit).
  • 1-Wire® –1 i 1-Wire® is a device communications bus system that provides low-speed data, signaling, and power over a single conductor.
  • Accelerometer i Accelerometer allows the device to indicate if vehicle is
    moving or not, as well as measure acceleration.
  • Battery –170mAh Li-ion 3,7V i Allows device to work without external power source
  • IP41 i Protected from tools and small wires, condensation.
  • 16MB memory i Internal memory for records storing when there is no GPRS connectivity.
  • 10 - 30V i External voltage range
  • Overvoltage protection i Protects device from voltage jumps till 90V
  • 1x SIM Card i Allows to put 1 SIM card for internet connection
  • USB 2.0 Interface i Device accessible and configurable via USB
  • FIRMWARE

  • LV-CAN support i LV-CAN200 is used to listen data from light vehicles. With this adapter FM device is able to collect and send such data.
  • ALL-CAN support i ALL-CAN300 is used to listen data from any type of transport: light vehicles, Trucks, busses, agriculture and other special transport. With this adapter FM device is able to collect and send such data.
  • Ignition detection i A vehicle ignition detection function, based on a configured ignition source (External power voltage, Digital input 1 or Movement).
  • Geo-fence i A functionality, which generates an event when crossing a defined area. It can be used to detect wherever car enters or leaves customized areas
  • Sleep/Deep sleep i Working modes which let FM device to reduce power consumption and save vehicle battery.
    - In sleep mode, FM device turns GNSS module off and it is not saving or sending new periodic data records.
    - In deep sleep mode, FM device sets GNSS receiver to sleep mode and turns off GSM/GPRS module, although periodic records with last known coordinate are being saved and sent to server.
  • Overspeeding detection i This scenario helps to prevent from exceeding fixed speed and inspects driver if needed. Digital output 1 is controlled by scenario for user needs, to manage buzzer, LED etc. During overspeeding event Digital output 1 will be turning ON and OFF until speed is lower than configured Max Allowed Speed.
  • FOTA i Firmware over the air solution. The software is used to send firmware/configuration to FM device via GPRS network.
  • Remote Log i This type of FM data logging is used when there is no possibility to connect to device physically. Device establishes GPRS connection and activates link to server, log is started to stream to server until set time is elapsed.
  • Garmin i Garmin provides a Fleet Management Interface Tool Kit, which connected to FM device via RS232 interface enables the driver to have a in their vehicle for real-time navigation, messaging, and job dispatch capabilities to help them be more efficient.
  • GPRS commands i It is possible to send commands to FM device using GPRS. GPRS commands can be used for sending configuration, debug, digital outputs control commands etc. These commands should be coded into a special codec12 format.
  • RFID RS232 i Radio-frequency identification (RFID) is the use of a wireless non-contact system to transfer data from a tag attached to an object, for the automatic driver identification. Reader can be connected to FM device via RS232 interface.
  • RFID 1-Wire® i Radio-frequency identification (RFID) is the use of a wireless non-contact system to transfer data from a tag attached to an object, for the automatic driver identification. Reader can be connected to FM device via 1-wire interface.
  • iButton 1-Wire® i iButton is a special driver identification chip based on 1-wire protocol. External 1-wire iButton reader can be used in parallel with FM devices
  • Temp. 1-Wire® i A temperature sensor which can be connected to FM device and provide information via 1-wire data protocol.
  • Immobilizer i With this scenario vehicle can be used only if iButton is connected. You can connect any iButton to pass Immobilizer security. FM device Digital Output 2 is controlled by scenario for user needs (for example: LED, buzzer or other indicator can be connected).
  • Green driving i Helps to prevent and inspect driver about harsh driving. This functionality works in parallel with accelerating force, braking force and cornering angles. Every harsh drive event can be presented in the real time during the LED or buzzer notification.
  • Fuel monitoring LLS i Fuel monitoring via LLS sensors gives ability to measurer are highly accurate fuel level in the vehicle. This functionality can be based on digital or analog connectivity.
  • Anti-jamming detection i Jamming detection informs the driver with buzzer or LED about radio jamming events.
  • NTP time synch. i Network time protocol (NTP) is used to get the right time without GPS connection. This functionality gives an ability to monitor the device state in the real time.
  • GNSS unplug detection i The GNSS unplug detection gives an ability to notify the User about GNSS antenna disassembly.
  • Transparent mode (RS232) i The RS232 is a standard used for a serial communication between devices. While using RS232 connection various type of data like fuel parameters or messages can be transmitted.
  • SMS event i SMS event is a special functionality which is used to notify the user about the tracker initial state. Any changes of speed, engine status, over speeding or etc. will be informed with SMS.
  • Odometer i Odometer is used to calculate traveled distance and produce this information directly to server.
  • Trip detection i Trip detection is used to inform user about start and stop points in the dedicated location, while engine is on or off.
  • Integrated scenarios i The integrated device scenarios are used to simply enable the dedicate functionality like Green driving, Over speeding, Authorized driving or Immobilizer.
  • Remote configuration over SMS i The remote configuration via SMS gives an ability to configure the device via SMS
  • Offline tracking i Offline tracking is used to track the object position while GPRS is not activated.
  • Auto Geofencing i Auto geofencing can detect wherever car enters or leaves customized areas with deactivated ignition.

Technical details

GSM:

  • Quad-band 900/1800 MHz; 850/1900 MHz
  • GPRS class 10 (up to 85,6 kbps)
  • SMS (text/data)

GPS/GLONASS:

  • NMEA protocol compatible. Messages:  GGA, GGL, GSA, GSV, RMC, VTG, TXT
  • 32 channel GPS/GLONASS receiver
  • Not less than -160 dBm

Interface:

  • 1 Digital Input
  • 1 Analog Input (10V or 30V range)
  • 1 Digital Open-collector Outputs (connecting external relays, LED, buzzers etc.)
  • 1Wire® temperature sensor
  • 1Wire® iButton
  • RS232/RS485
  • Motion sensor
  • Power supply (+10…+30)  V DC
  • Internal  GSM antenna
  • Internal  GPS/GLONASS antenna
  • Integrated back-up battery
  • Dimensions: L(65mm)xW(56,6mm)xH(18,9mm)
  • 2 Status LEDs
  • Configuration and firmware upload (FOTA and via cable )

Features:

  • Small and easy to mount case
  • Internal GSM antenna and Internal GPS/GLONASS antenna allow mount FM1125 much easier. There is also optional external GPS/GLONASS antenna
  • Real Time tracking
  • Smart data acquisition – based on time, distance, angle, ignition and  I/O events allow to have precise online
  • tracker
  • Sending acquired data via GPRS (TCP/IP and UDP/IP protocols)
  • Smart algorithm of GPRS connections for GPRS traffic saving
  • Operating in roaming networks by preferred GSM providers list
  • Events from I/O elements detection and sending via GPRS or SMS
  • Scheduled 24 coordinates SMS sending when GPRS not available
  • 5 geofence zones (rectangular or circle)
    • Auto Geofencing for car towing detection and car theft prevention
  • Deep Sleep mode (less than 2 mA power consumption)
  • FOTA (firmware and configuration updating via GPRS)
  • 3 operational modes (Home, Roaming, Unknown) based on operator codes
  • Integrated scenarios:
    • Over speeding to secure driver and prevent penalties
    • Trip start and end detection
  • LV-CAN200 support
  • RS232/RS485 peripherial device support:
    • GARMIN FMI support
    • Digital LLS fuel sensors support
    • RFID protocol support

Downloads