FM1122
FM1122FM1122FM1122

FM1122 – external GPS antenna with battery

Small tracker with external GPS/GLONASS antenna and internal battery

Technology
  • SMS
  • GPRS
  • GNSS
Hardware
  • Battery
  • 1-Wire®
  • DOUT
  • External GNSS antenna
Firmware
  • Trip detection
  • Immobilizer
  • ALL-CAN support
  • LV-CAN support

Compare products
(Compare 2 or up to 4 products)

Product Description

Small tracker with external GPS/GLONASS antenna and internal battery

  • Internal GSM antenna
  • External GPS/GLONASS antenna
  • Integrated  backup battery
  • LV-CAN200, ALL-CAN300 functionality support
  • Integrated scenarios (Overspeeding, Authorized driving , Immobilizer)

FM1122 Scheme

FM1122T542SC* package contains

  • FM1122 tracker.
  • Mini USB – USB cable (0.8 m).
  • Input/output power supply cable (0.9 m).
  • GPS/GLONASS antenna (3.0 m).

* SAMPLES ordering code – applied for orders up to 7 pcs.

FM1122T54201* package contains

  • FM1122 tracker.
  • Mini USB – USB cable (0.8 m).
  • Input/output power supply cable (0.9 m).
  • GPS/GLONASS antenna (3.0 m).

* MASS PACKAGING – for bigger quantity orders, with configuration cable included.

FM1122T5CG01* package contains

  • FM1122 tracker.
  • Input/output power supply cable (0.9 m).
  • GPS/GLONASS antenna (3.0 m).

* MASS PACKAGING – for bigger quantity orders, configuration cable not included.

  • TECHNOLOGY

  • GNSS i Global positiong system/Global Navigation Satellite System.
  • GPRS i General Packet Radio Service (GPRS) is a packet oriented mobile data service based on the 2G technology.
  • SMS i Short Message Service (SMS) is a text messaging service component.
  • HARDWARE

  • Internal GSM antenna i An antenna used for GSM connectivity. Integrated into FM device PCB. Does not have external connector.
  • External GNSS antenna i An antenna used for GPS connectivity. Connected to FM device via external connector.
  • DIN – digital input –3 i Digital Inputs allow device to detect logic states 1 (enabled) or 0 (disabled).
  • AIN - analog input –1 i An analog input converts a voltage level into a digital value that can be stored and processed in device.
  • DOUT –2 i Digital Outputs allow device to output logic states 1 (makes a circuit) and 0 (cuts the circuit).
  • 1-Wire® –1 i 1-Wire® is a device communications bus system that provides low-speed data, signaling, and power over a single conductor.
  • Accelerometer i Accelerometer allows the device to indicate if vehicle is
    moving or not, as well as measure acceleration.
  • Battery –170mAh Li-ion 3,7V i Allows device to work without external power source
  • IP41 i Protected from tools and small wires, condensation.
  • 1MB memory i Internal memory for records storing when there is no GPRS connectivity.
  • 10 - 30V i External voltage range
  • Overvoltage protection i Protects device from voltage jumps till 90V
  • 1x SIM Card i Allows to put 1 SIM card for internet connection
  • USB 2.0 Interface i Device accessible and configurable via USB
  • FIRMWARE

  • LV-CAN support i LV-CAN200 is used to listen data from light vehicles. With this adapter FM device is able to collect and send such data.
  • ALL-CAN support i ALL-CAN300 is used to listen data from any type of transport: light vehicles, Trucks, busses, agriculture and other special transport. With this adapter FM device is able to collect and send such data.
  • Ignition detection i A vehicle ignition detection function, based on a configured ignition source (External power voltage, Digital input 1 or Movement).
  • Geo-fence i A functionality, which generates an event when crossing a defined area. It can be used to detect wherever car enters or leaves customized areas
  • Sleep/Deep sleep i Working modes which let FM device to reduce power consumption and save vehicle battery.
    - In sleep mode, FM device turns GNSS module off and it is not saving or sending new periodic data records.
    - In deep sleep mode, FM device sets GNSS receiver to sleep mode and turns off GSM/GPRS module, although periodic records with last known coordinate are being saved and sent to server.
  • Overspeeding detection i This scenario helps to prevent from exceeding fixed speed and inspects driver if needed. Digital output 1 is controlled by scenario for user needs, to manage buzzer, LED etc. During overspeeding event Digital output 1 will be turning ON and OFF until speed is lower than configured Max Allowed Speed.
  • FOTA i Firmware over the air solution. The software is used to send firmware/configuration to FM device via GPRS network.
  • Remote Log i This type of FM data logging is used when there is no possibility to connect to device physically. Device establishes GPRS connection and activates link to server, log is started to stream to server until set time is elapsed.
  • GPRS commands i It is possible to send commands to FM device using GPRS. GPRS commands can be used for sending configuration, debug, digital outputs control commands etc. These commands should be coded into a special codec12 format.
  • RFID 1-Wire® i Radio-frequency identification (RFID) is the use of a wireless non-contact system to transfer data from a tag attached to an object, for the automatic driver identification. Reader can be connected to FM device via 1-wire interface.
  • iButton 1-Wire® i iButton is a special driver identification chip based on 1-wire protocol. External 1-wire iButton reader can be used in parallel with FM devices
  • Temp. 1-Wire® i A temperature sensor which can be connected to FM device and provide information via 1-wire data protocol.
  • Immobilizer i With this scenario vehicle can be used only if iButton is connected. You can connect any iButton to pass Immobilizer security. FM device Digital Output 2 is controlled by scenario for user needs (for example: LED, buzzer or other indicator can be connected).
  • Green driving i Helps to prevent and inspect driver about harsh driving. This functionality works in parallel with accelerating force, braking force and cornering angles. Every harsh drive event can be presented in the real time during the LED or buzzer notification.
  • Anti-jamming detection i Jamming detection informs the driver with buzzer or LED about radio jamming events.
  • NTP time synch. i Network time protocol (NTP) is used to get the right time without GPS connection. This functionality gives an ability to monitor the device state in the real time.
  • SMS event i SMS event is a special functionality which is used to notify the user about the tracker initial state. Any changes of speed, engine status, over speeding or etc. will be informed with SMS.
  • Odometer i Odometer is used to calculate traveled distance and produce this information directly to server.
  • Trip detection i Trip detection is used to inform user about start and stop points in the dedicated location, while engine is on or off.
  • Integrated scenarios i The integrated device scenarios are used to simply enable the dedicate functionality like Green driving, Over speeding, Authorized driving or Immobilizer.
  • Remote configuration over SMS i The remote configuration via SMS gives an ability to configure the device via SMS
  • Offline tracking i Offline tracking is used to track the object position while GPRS is not activated.
  • Auto Geofencing i Auto geofencing can detect wherever car enters or leaves customized areas with deactivated ignition.

Technical details

GSM:

  • Quad-band 900/1800 MHz; 850/1900 MHz
  • GPRS class 10 (up to 85,6 kbps);
  • SMS (text/data)

GPS/GLONASS:

  • NMEA protocol compatible. Messages: GGA, GGL, GSA, GSV, RMC, VTG, TXT
  • 32 channel GPS/GLONASS receiver
  • Not less than -160 dBm

Interface:

  • 1 Digital Input Reserved for Ignition Status Monitoring
  • 2 Digital Inputs
  • 1 Analog Input (10V or 30V range)
  • 2 Digital Open-collector Outputs (connecting external relays, LED, buzzers etc.)
  • 1-Wire® temperature sensor
  • 1-Wire® iButton
  • Motion sensor
  • Power supply (+10…+30) V DC
  • Internal GSM antenna
  • External GPS/GLONASS antenna
  • Integrated backup battery
  • 2 Status LEDs
  • USB Port
  • Configuration and firmware upload (FOTA and via USB cable)

Features:

  • Small and easy to mount case
  • Internal  GSM  antenna  and External  GPS/GLONASS antenna  for  easy  mounting and  best  performance
  • GPS/GLONASS and I/O data acquisition
  • Real Time tracking
  • Smart algorithm of data acquisition (time, distance, angle, ignition and event based)
  • Sending acquired data via GPRS (TCP/IP and UDP/IP protocols)
  • Smart algorithm of GPRS connections (GPRS traffic saving)
  • Operating in roaming networks (preferred GSM providers list)
  • Events on I/O detection and sending via GPRS or SMS.
  • Scheduled 24 coordinates SMS sending
  • 5 geofence zones (rectangular or circle)
    • Auto  Geofencing  crested  for  car  towing  detection  and  car  theft  prevention
  • Deep Sleep mode (less  than  2  mA power  consumption)
  • FOTA (firmware updating via GPRS)
  • 3  operational  modes (Home,  Roaming,  Unknown)  based  on  operator
  • Integrated  scenarios:
    • Over  speeding  to  secure  driver  and  prevent  penalties
    • Immobilizer  function
    • Authorized  driving  (1-Wire®  iButton  ID  keys  up  to  50  iButton  keys)use  to  prevent  stealing  or indicate  drivers
    • Trip  start  and  end  detection
  • FM1122  supports  a  remote  logs  reading
    • FM1122  supports  remote  diagnostic  logs  functionality  using  GPRS.  Possible  issues  resolving  becomes faster .  Manufacturer can  read  logs  remotely  using  SMS/GPRS  to  diagnose  the  FM1122  and  timely  respond to  the  fault

Downloads